• Masuk ke file konfigurasi berikut

[root@localhost ~]# nano /etc/default/grub 

• Setelah itu edit pada baris enam

GRUB_CMDLINE_LINUX="ipv6.disable=1
rd.lvm.lv=fedora-server/root..... 

• Kemudian save dan load kembali grub nya dengan perintah berikut, dan kembali restart

[root@localhost ~]# grub2-mkconfig -o /boot/grub2/grub.cfg

[root@localhost ~]# reboot 

• Setelah di restart coba cek kembali settingan ip nya dengan perintah ifconfig atau ip address

Ya, Sekian dulu dari saya, semoga bermanfaat. terima kasih

The post CentOS 7 : Cara disable IPv6 pada CentOS 7 appeared first on ReshaJTama.

• Setting Hostname

[root@localhost ~]# hostnamectl set-hostname reshajtama.my.id 

• Mendisplay interface

[root@localhost ~]# nmcli d

DEVICE       TYPE      STATE      CONNECTION
eth0         ethernet  connected  eth0
lo           loopback  unmanaged  --

• Setting IPv4 dengan nmcli

[root@localhost ~]# nmcli c modify eth0 ipv4.addresses 192.168.1.10/24 

• Setting Default gateway

[root@localhost ~]# nmcli c modify eth0 ipv4.gateway 192.168.1.1

• Setting DNS (Domain Name Server)

nmcli c modify eth0 ipv4.dns 8.8.8.8

• Restart & reload setting

[root@localhost ~]# nmcli c down eth0; nmcli c up eth0

Connection successfully activated (D-Bus active path: /org/freedesktop/NetworkManager/ActiveConnection/1) 

• Melihat semua settingan itu

[root@localhost ~]# ip addr show

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
    link/ether 00:0c:29:cd:9c:2d brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.10/24 brd 192.168.1.255 scope global eth0
       valid_lft forever preferred_lft forever
    inet6 fe80::20c:29ff:fecd:9c2d/64 scope link
       valid_lft forever preferred_lft forever

ya berikut adalah bagaimana kita memanagement ip address, hostname dan DNS pada Centos 7.

The post CentOS 7 : Konfigurasi IP Address & Hostname pada CentOS 7 appeared first on ReshaJTama.

Firewall adalah sebuah system yang di rancang untuk memblok akses jaringan yang tidak di inginkan pada suatu jaringan internal. sedangkan SELinux (Security Enchaned Linux) itu sendiri adalah sebuah system security yang sudah ada pada Distro turunan Redhat, Centos dan seterus nya.

Terkadang kita tidak bisa mengakses hal – hal tertentu karena kebijakan dari SELinux dan Firewall itu sendiri. Oleh karena itu kita perlu memanagement nya agar sesuai dengan kebutuhan kita.

• Management Firewall

Untuk memanagement Firewall anda bisa melihat status dari Firewall tersebut dengan perintah berikut :

[root@reshajtama ~]# systemctl status firewalld 
● firewalld.service - firewalld - dynamic firewall daemon
   Loaded: loaded (/usr/lib/systemd/system/firewalld.service; disabled; vendor preset: enabled)
   Active: active (running) since Thu 2015-03-31 19:36:27 JST; 2s ago
 Main PID: 1308 (firewalld)
   CGroup: /system.slice/firewalld.service
           └─1308 /usr/bin/python -Es /usr/sbin/firewalld --nofork --nopid

Untuk menghentikan firewall sementara, kita bisa menggunakan perintah berikut :

[root@reshajtama ~]# systemctl stop firewalld

untuk mendisable firewall agar tidak berjalan saat startup bisa menggunakan perintah berikut :

[root@reshajtama ~]# systemctl disable firewalld 

• Management SELinux

Untuk melihat apakah SELinux berjalan atau tidak bisa menggunakan perintah berikut :

[root@reshajtama ~]# sestatus

atau dengan menggunakan perintah

[root@reshajtama ~]# getenforce

untuk menghentikan atau mengubah status dari SELinux itu sendiri dapat dengan mengubah file konfig dari SELinux itu sendiri , seperti berikut :

[root@reshajtama ~]# vi /etc/selinux/config

# This file controls the state of SELinux on the system.
# SELINUX= can take one of these three values:
#     enforcing - SELinux security policy is enforced.
#     permissive - SELinux prints warnings instead of enforcing.
#     disabled - No SELinux policy is loaded.
SELINUX=disabled   # change to disabled
# SELINUXTYPE= can take one of these two values:
#     targeted - Targeted processes are protected,
#     minimum - Modification of targeted policy. Only selected processes are protected.
#     mls - Multi Level Security protection.
SELINUXTYPE=targeted

Oke sekian dari saya, terima kasih telah berkunjung. semoga bermanfaat.

The post CentOS 7 : Setting Firewall & SELinux di CentOS appeared first on ReshaJTama.

• Menambahkan User dan setting password di CentOS 7

[root@reshajtama ~]# useradd newuser 
[root@reshajtama ~]# passwd cent
Changing password for user cent.
New UNIX password:# set password
Retype new UNIX password:# confirm
passwd: all authentication tokens updated successfully.
[root@reshajtama ~]# exit     #Keluar dari User tersebut

• Coba untuk login ke User yang di buat tadi dengan logout terlebih dahulu

reshajtama login: newuser                 #User yang tadi di buat
password: # password
[newuser@reshajtama ~]$ su                #Masuk ke root Akses
Password:# root password
[root@reshajtama ~]#

• Membuat user “newuser” menjadi user menjadi setara dengan root

[root@reshajtama ~]# usermod -G wheel newuser
[root@reshajtama ~]# vi /etc/pam.d/su

kemudian hapus tanda pagar pada baris berikut

# uncomment pada baris ini
auth            required        pam_wheel.so use_uid

• kita bisa mengakses ftp sebagai root tetapi menggunakan user ‘newuser’, sebelumnya kita harus memberikan settingan seperti berikut

[root@reshajtama ~]# vi /etc/aliases
# Person who should get root's mail
# last line: uncomment and change to a user
root: newuser
[root@reshajtama ~]# newaliases                   # reload aliases

terima kasih telah berkunjung, semoga bermanfaat.

The post CentOS 7 : Menambahkan User dan Mengedit Password di CentOS 7 appeared first on ReshaJTama.

Pertama download terlebih dahulu ISO dan CentOS 7 di link berikut

http://isoredirect.centos.org/centos/7.6.1810/isos/x86_64/

Setelah selesai di download, silahkan siapkan CD/DVD kosong dan masukan ke DVD ROM. kemudian klik kanan kemudian pilih burn to disc seperti berikut menggunakan Ultra ISO, Power ISO, atau aplikasi Burning lainnya.

Setelah itu tinggal tunggu hingga proses Burning nya selesai.

The post CentOS 7 : Download dan Burning Centos appeared first on ReshaJTama.

useradd myUser

dan untuk men setting password nya silahkan masukan perintah berikut :

passwd myUser

Kemudian jika anda ingin user itu dapat hak akses sama dengan root, masuk ke settingan berikut dan tambahkan script berikut di paling bawah.

nano /etc/aliases

kemudian tambahkan di paling bawah seperti ini

#  Aliases in this file will NOT be expanded in the header from
#  Mail, but WILL be visible over networks or from /bin/mail.
#
#       >>>>>>>>>>      The program "newaliases" must be run after
#       >> NOTE >>      this file is updated for any changes to
#       >>>>>>>>>>      show through to sendmail.
#

# Basic system aliases -- these MUST be present.
mailer-daemon:  postmaster
postmaster:     root

# General redirections for pseudo accounts.
bin:            root
daemon:         root
adm:            root
lp:             root
sync:           root
root:           myUser

kemudian reload service nya dengan perintah berikut :

newaliases

kemudian coba lagi masuk dengan user tersebut untuk edit file yang mempunyai privilage root

The post Cara membuat User yang setara Root di Centos appeared first on ReshaJTama.

Kalian jangan khawatir, karena kalian hanya perlu menginstall package berikut agar dapat terkoneksi dengan windows.

yum install -y freerdp 

setelah selesai install. anda tinggal menjalankan perintah berikut :

xfreerdp 0g 800x600 -u myUsers 192.168.1.1
connected to 192.168.1.1:3389
Password: #masukan password nya

# -g = Resolusi layar
# -u = Users RDP nya

Dan anda akhirnya dapat terkoneksi dengan layanan RDP milik si Windows

The post Cara Remote Windows Dengan RDP dari Centos appeared first on ReshaJTama.

Kalian yang mempunyai Basic Jaringan pasti mengetahui betul perangkat ini. Mikrotik adalah vendor Router dan Switch yang sangat populer, karena harganya murah dan memiliki banyak Fungsi yang berguna.

Tapi, perlu kalian ketahui, perangkat ini mempunyai bug pada versi 6.29 (release date: 2015/28/05) sampai 6.42 (release date 2018/04/20) nya. kalian bisa mendapat kan user dan password nya dengan mudah dengan cara meng Exploit perangkat ini. Berikut adalah caranya :

• Anda harus menginstall Python 3

• Silahkan anda download file nya di link berikut

https://github.com/BigNerd95/WinboxExploit

• Anda bisa menggunakan Git Clone atau pun mendownload nya dan mengunzip nya seperti biasa
• Setelah selesai anda bisa menjalankan perintah berikut

python3 WinboxExploit.py 10.10.10.1

User: admin
Pass: passwd

• Anda juga bisa men Scan Perangkat Miktorik nya dengan Perintah

python3 MACServerDiscover.py
Looking for Mikrotik devices (MAC servers)

    aa:aa:aa:aa:aa:aa 

    bb:bb:bb:bb:bb:bb

• Anda juga dapat meng exploit nya melalui Mac Address nya dengan perintah berikut

python3 MACServerExploit.py aa:aa:aa:aa:aa:aa

User: admin
Pass: passwd

Mudah bukan, tolong di gunakan dengan bijak dan jangan di salah gunakan. Semoga bisa membantu anda dan terima kasih sudah berkunjung.

The post Hack Mikrotik dengan Python untuk mendapatkan User Dan Password Login appeared first on ReshaJTama.

Oke, langsung saja ke step – step nya.

• Pertama kalian harus download file dari Cisco Packet Tracert nya. Kalian bisa mendownload di official Page dari Cisco nya sendiri.
• Setelah mendownload, silahkan kalian masuk ke Terminal dan berikan akses untuk file tersebut

chmod -R 755 "Packet Tracert.tar.gz"

• Setelah itu unzip file tar.gz nya dengan perintah berikut

tar -xvf "Packet Tracert.tar.gz"

• Tunggu file tersebut akan meng exstrak semua file nya.

• Setelah selesai, jalankan perintah berikut

./install

• Kemudian anda tunggu sampai selesai penginstallan nya
• Jika ada permintaan Persetujuan EULA, anda ketik “Yes” saja

• Setelah anda install, anda dapat memanggil packet tracer dari terminal dengan perintah berikut

packettracer

Ya, seperti itu lah teman – teman. selamat belajar packet tracer di linux anda. semoga artikel ini bermanfaat, terima kasih telah berkunjung

The post Install Packet Tracert di Linux appeared first on ReshaJTama.

Sebagai study kasus nya seperti ini. disini saya mempunyai komputer dengan IP 192.168.1.1 dengan system operasi Linux, saya ingin mengakses file Document yang ada di IP 192.168.1.1 dari komputer saya yang mempunyai system operasi Windows dengan IP 192.168.1.2. Jadi bagaimana solusi nya. Ya, saat nya kita gunakan SAMBA Server ini.

Berikut step – step nya :

• Install package SAMBA nya dengan terminal

sudo apt-get install samba

• Kemudian masuk ke file konfigurasi SAMBA nya di

nano /etc/samba/smb.conf

• kemudian akan muncul file seperti ini

#
# Sample configuration file for the Samba suite for Debian GNU/Linux.
#
#
# This is the main Samba configuration file. You should read the
# smb.conf(5) manual page in order to understand the options listed
# here. Samba has a huge number of configurable options most of which 
# are not shown in this example
#
# Some options that are often worth tuning have been included as
# commented-out examples in this file.
#  - When such options are commented with ";", the proposed setting
#    differs from the default Samba behaviour
#  - When commented with "#", the proposed setting is the default
#    behaviour of Samba but the option is considered important
#    enough to be mentioned here
#
# NOTE: Whenever you modify this file you should run the command
# "testparm" to check that you have not made any basic syntactic 
# errors. 

#======================= Global Settings =======================

[global]

## Browsing/Identification ###

# Change this to the workgroup/NT-domain name your Samba server will part of
   workgroup = WORKGROUP

# server string is the equivalent of the NT Description field
	server string = %h server (Samba, Linux Mint)

# Windows Internet Name Serving Support Section:
# WINS Support - Tells the NMBD component of Samba to enable its WINS Server
#   wins support = no

# WINS Server - Tells the NMBD components of Samba to be a WINS Client
# Note: Samba can be either a WINS Server, or a WINS Client, but NOT both
;   wins server = w.x.y.z

# This will prevent nmbd to search for NetBIOS names through DNS.
   dns proxy = no

#### Networking ####

# The specific set of interfaces / networks to bind to
# This can be either the interface name or an IP address/netmask;
# interface names are normally preferred
;   interfaces = 127.0.0.0/8 eth0

# Only bind to the named interfaces and/or networks; you must use the
# 'interfaces' option above to use this.
# It is recommended that you enable this feature if your Samba machine is
# not protected by a firewall or is a firewall itself.  However, this
# option cannot handle dynamic or non-broadcast interfaces correctly.
;   bind interfaces only = yes



#### Debugging/Accounting ####

# This tells Samba to use a separate log file for each machine
# that connects
   log file = /var/log/samba/log.%m

# Cap the size of the individual log files (in KiB).
   max log size = 1000

# If you want Samba to only log through syslog then set the following
# parameter to 'yes'.
#   syslog only = no

# We want Samba to log a minimum amount of information to syslog. Everything
# should go to /var/log/samba/log.{smbd,nmbd} instead. If you want to log
# through syslog you should set the following parameter to something higher.
   syslog = 0

# Do something sensible when Samba crashes: mail the admin a backtrace
   panic action = /usr/share/samba/panic-action %d


####### Authentication #######

# Server role. Defines in which mode Samba will operate. Possible
# values are "standalone server", "member server", "classic primary
# domain controller", "classic backup domain controller", "active
# directory domain controller". 
#
# Most people will want "standalone sever" or "member server".
# Running as "active directory domain controller" will require first
# running "samba-tool domain provision" to wipe databases and create a
# new domain.
   server role = standalone server

# If you are using encrypted passwords, Samba will need to know what
# password database type you are using.  
   passdb backend = tdbsam

   obey pam restrictions = yes

# This boolean parameter controls whether Samba attempts to sync the Unix
# password with the SMB password when the encrypted SMB password in the
# passdb is changed.
   unix password sync = yes

# For Unix password sync to work on a Debian GNU/Linux system, the following
# parameters must be set (thanks to Ian Kahan <<kahan@informatik.tu-muenchen.de> for
# sending the correct chat script for the passwd program in Debian Sarge).
   passwd program = /usr/bin/passwd %u
   passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* .

# This boolean controls whether PAM will be used for password changes
# when requested by an SMB client instead of the program listed in
# 'passwd program'. The default is 'no'.
   pam password change = yes

# This option controls how unsuccessful authentication attempts are mapped
# to anonymous connections
   map to guest = bad user

########## Domains ###########

#
# The following settings only takes effect if 'server role = primary
# classic domain controller', 'server role = backup domain controller'
# or 'domain logons' is set 
#

# It specifies the location of the user's
# profile directory from the client point of view) The following
# required a [profiles] share to be setup on the samba server (see
# below)
;   logon path = \\%N\profiles\%U
# Another common choice is storing the profile in the user's home directory
# (this is Samba's default)
#   logon path = \\%N\%U\profile

# The following setting only takes effect if 'domain logons' is set
# It specifies the location of a user's home directory (from the client
# point of view)
;   logon drive = H:
#   logon home = \\%N\%U

# The following setting only takes effect if 'domain logons' is set
# It specifies the script to run during logon. The script must be stored
# in the [netlogon] share
# NOTE: Must be store in 'DOS' file format convention
;   logon script = logon.cmd

# This allows Unix users to be created on the domain controller via the SAMR
# RPC pipe.  The example command creates a user account with a disabled Unix
# password; please adapt to your needs
; add user script = /usr/sbin/adduser --quiet --disabled-password --gecos "" %u

# This allows machine accounts to be created on the domain controller via the 
# SAMR RPC pipe.  
# The following assumes a "machines" group exists on the system
; add machine script  = /usr/sbin/useradd -g machines -c "%u machine account" -d /var/lib/samba -s /bin/false %u

# This allows Unix groups to be created on the domain controller via the SAMR
# RPC pipe.  
; add group script = /usr/sbin/addgroup --force-badname %g

############ Misc ############

# Using the following line enables you to customise your configuration
# on a per machine basis. The %m gets replaced with the netbios name
# of the machine that is connecting
;   include = /home/samba/etc/smb.conf.%m

# Some defaults for winbind (make sure you're not using the ranges
# for something else.)
;   idmap uid = 10000-20000
;   idmap gid = 10000-20000
;   template shell = /bin/bash

# Setup usershare options to enable non-root users to share folders
# with the net usershare command.

# Maximum number of usershare. 0 (default) means that usershare is disabled.
;   usershare max shares = 100

# Allow users who've been granted usershare privileges to create
# public shares, not just authenticated ones
   usershare allow guests = yes

#======================= Share Definitions =======================

# Un-comment the following (and tweak the other settings below to suit)
# to enable the default home directory shares. This will share each
# user's home directory as \\server\username
;[homes]
;   comment = Home Directories
;   browseable = no

# By default, the home directories are exported read-only. Change the
# next parameter to 'no' if you want to be able to write to them.
;   read only = yes

# File creation mask is set to 0700 for security reasons. If you want to
# create files with group=rw permissions, set next parameter to 0775.
;   create mask = 0700

# Directory creation mask is set to 0700 for security reasons. If you want to
# create dirs. with group=rw permissions, set next parameter to 0775.
;   directory mask = 0700

# By default, \\server\username shares can be connected to by anyone
# with access to the samba server.
# Un-comment the following parameter to make sure that only "username"
# can connect to \\server\username
# This might need tweaking when using external authentication schemes
;   valid users = %S

# Un-comment the following and create the netlogon directory for Domain Logons
# (you need to configure Samba to act as a domain controller too.)
;[netlogon]
;   comment = Network Logon Service
;   path = /home/samba/netlogon
;   guest ok = yes
;   read only = yes

# Un-comment the following and create the profiles directory to store
# users profiles (see the "logon path" option above)
# (you need to configure Samba to act as a domain controller too.)
# The path below should be writable by all users so that their
# profile directory may be created the first time they log on
;[profiles]
;   comment = Users profiles
;   path = /home/samba/profiles
;   guest ok = no
;   browseable = no
;   create mask = 0600
;   directory mask = 0700

[printers]
   comment = All Printers
   browseable = no
   path = /var/spool/samba
   printable = yes
   guest ok = no
   read only = yes
   create mask = 0700

# Windows clients look for this share name as a source of downloadable
# printer drivers
[print$]
   comment = Printer Drivers
   path = /var/lib/samba/printers
   browseable = yes
   read only = yes
   guest ok = no
# Uncomment to allow remote administration of Windows print drivers.
# You may need to replace 'lpadmin' with the name of the group your
# admin users are members of.
# Please note that you also need to set appropriate Unix permissions
# to the drivers directory for these users to have write rights in it
;   write list = root, @lpadmin

[Foldershare]
   comment = "My Sharing Files" # Tag Comment
   browseable = Yes #akses untuk mencari file
   path = /myfoldershare #ffolder yang ingin di akses
   guest ok = no # mengizinkan user anonym atau guest untuk mengakses
   read only = yes # Hanya dapat melihat, tidak dapat mengedit
   writeable = yes # dapat mengedit file

Tambahkan Foldershare berikut di akhir dari script.

• kemudian kita buat user untuk dapat mengakses SAMBA Server kita dengan perintah

adduser user01

• Lalu masukan perintah berikut untuk memberikan akses user tersebut ke SAMBA

smbpasswd -a user01

Kemudian masukan password yang akan di gunakan oleh user tersebut. dan SAMBA Server sudah dapat di gunakan untuk Folder Share dengan komputer lain.

Jika ada pertanyaan, silahkan komentar di bawah. Terima kasih

The post Membuat SAMBA Server untuk folder Sharing di Linux appeared first on ReshaJTama.